该词条未找到_海词词典

您要查找的是不是：

Keywords Squeezing Casting;Metallic Casting;Liquid Forging;Die Design;Sub-oil Cyclinder; 挤压铸造;金属型铸造;液态模锻;模具设计;副油缸;
Keywords Squeeze casting;Preform;Particulate;Metal matrix composite; 挤压铸造;预制块;颗粒;金属基复合材料;
Keywords squeeze casting;zine base alloy;wear resistance;precipitation hardening; 挤压铸造;锌合金;耐磨性;沉淀硬化;
Selection principle on the squeezing casting techniques was discussed. 论述了挤压铸造技术方案的选择原则。
A new technology of squeezing casting for small piston is developed successfully with old Y41-63 type equipment. 用Y41－63型旧设备，开发挤压小活塞新工艺获得成功。
Design of squeezing die as well as good quality and low cost of piston with squeezing casting are introduced. 介绍了挤压模的设计以及挤压活塞的优质和低成本。
The lower specific pressure and delay pressurization in time during casting process were responsible for surface blister and cold shut of motor cycle wheel in squeezing casting. 分析了实际铸造比压偏小以及不能瞬间及时增压是造成摩托车车轮挤压铸件表面起泡和冷隔的主要原因。
It is pointed out that the rational squeezing casting technology can refine microstructure and improve the component compactness as well as the mechanical properties of alloy. 指出合理的挤压铸造工艺可细化合金显微组织,提高铸件致密性,改善合金力学性能。
Effects of heat treatment on microstructure of aluminosilicate short fiber reinforced ZL108 composites prepared by squeezing casting have been observed. 研究了热处理工艺对挤压铸造制备的硅酸铝短纤维增强ZL108合金复合材料组织的影响。
The squeezing casting of Zn-Al alloy merges the advantage of casting and forging and has the broad development under the situation of more and more high demand to casting quality. 锌铝合金挤压铸造结合了挤压铸造和锌铝合金的优点,在当今对铸件质量要求越来越高的形势下,具有广阔的发展前景。
Mold filling smoothly with low speed and large flow rate as well as instant pressurization in time conformed to the basic principles of squeezing casting. 论述了以低速、大流量、平稳充填铸型并在瞬间及时增压是挤压铸造的基本原理。
The lowerspecificpressure and delay pressurizat in time during casting process were responsible for surface blister and cold shut of motor cycle wheel in squeezing casting. 分析了实际铸造比压偏小以及不能瞬间及时增压是造成摩托车车轮挤压铸件表面起泡和冷隔的主要原因。
Keywords Mg alloys;Autocycle wheels;Squeezing casting; 镁合金;轮毂;液态挤压铸造;
Control Arm of Automobile in Squeezing Casting 汽车控制臂挤压铸造工艺研究
Squeezing Casting of Mg Alloys Wheels of Autocycle 镁合金摩托车轮毂液态挤压铸造
Squeeze casting is descrbed as having a combination of the virtues of gravity die casting and closed die forging. 挤压铸造被认为兼具有压力铸造和合模俦造的优点。
The aluminium based composite reinforced by alumina Borate Whisker was prepared by squeeze casting method. 本文利用挤压铸造法成功地制备了硼酸铝晶须增强铝复合材料。
Keywords squeezing roll 45 grade of steel boriding quenching temper hardness; 挤压辊;45钢;渗硼;淬火;回火;硬度;
There are four main technological methods:powder metallurgy,liquid infiltration,squeeze casting and compocasting. 制造方法有：粉末冶金法、液态浸渗法、压铸法、熔搅铸造法。
Influence of heat treatment on the microstructure and mechanical properties of ZA43 Mn alloy in punch squeeze casting has been studied. 研究了热处理对冲头式挤压铸造ZA43 Mn合金显微组织和力学性能的影响。